Understanding Cisco Access Point IOS Images
Introduction
All Cisco Aironet wireless access points and bridges were shipped in general with an IOS Software.
The only exception is the OEAP602.
Note:Some older Cisco access points did not run IOS, such as the Aironet 340 which ran only VxWorks, and the 1000 series lightweight APs.
Access Point IOS is distributed as a tar file. These tar files can be downloaded from cisco.com SDS; lightweight IOS images (k9w8) are also bundled in
the WLC software images (.aes). The IOS image names include the following components.
platform–featureset-tar.version.tar
- ap1g1 – 700 series (702w beginning with 15.2(4)JB5)
- ap1g2 – 1600 series
- ap1g3 – 1530 series
- ap3g2 – 3700/3600/2700/2600 series (3700 supported beginning with 15.2(4)JB; 2700 beginning with 15.2(4)JB5)
- ap3g1 – 3500/1260 series
- ap802 – AP embedded in 819, 812, 886VA-W/887VA-W, C88x and C88x routers
- ap801 – AP embedded in 861W, most 88xW, and 1911W routers
- apw5100 – Rockwell Stratix 5100 WAPAK9, WAPCK9, WAPEK9, WAPZK9
- c1520 – 1550 and 1520 series mesh APs
- c1410 – BR1410
- c1310 – BR1310
- c1250 – 1250 series APs
- c1240 – 1240 series APs
- c1200 – 1200 series (1200/1210/1220/1230)
- c1140 – 1140 and 1040 series APs
- c1130 – 1130 series APs
- c1100 – 1100 series APs (i.e. the AP1121)
- c520 – 521 AP
- c350 – 350 series APs
featureset – the set of software features supported by the image – one of:
- k9w7 – autonomous ( or “site survey”) IOS
- k9w8 – full lightweight IOS (this is what is bundled in the WLC .aes image, and is factory installed on “mesh” APs)
- rcvk9w8 – lightweigt recovery image – this is factory installed on lightweight APs, unless a “mesh” image is specified; it lacks radion firmware
- boot – bootloader image (not IOS) – normally installed by manufacturing and not updated in the field
version – the IOS version
- There is a 1:1 mapping between the lightweight IOS software version (such as 12.4(23c)JA) and the CUWN version (such as 7.0.98.0)
- see the Wireless Solutions Software Compatibility Matrix on CCO
Example
c1240–k9w7-tar.124-25d.JA1.tar
- Platform: c1240: 1240 series AP
- Featureset: k9w7: autonomous IOS
- Version: 124-25d.JA1: 12.4(25d)JA1
As AP IOS is always distributed as a tar file, the AP cannot directly execute such a file (thus, if you were to copy c1240-k9w7-tar.124.25d.JA1.tar directly onto AP flash, and then try
try to boot it, this could not work.) The tar file contains, in addition to the IOS image proper , the radio firmware files, the HTML GUI files (if present), and various other files.
The AP IOS tar file must be unbundled into AP flash using the archive exec command (this is done in
an automated fashion when lightweight AP is upgraded after joining a WLC.)
How to handle the AP flash and how to set an AP to factory default
